Factory Supply 4.5×4.5 Tact Switch - manufacturer 4.5×4.5 4 pin DIP tact switch – Shouhan
Factory Supply 4.5×4.5 Tact Switch - manufacturer 4.5×4.5 4 pin DIP tact switch – Shouhan Detail:
5A INSULATION RESISTANCE
Measurements shall be made following Application of DC100V potential across terminals and across terminals and fuame for 1minute,100MΩ min
5B WITHSTAND VILTAGE
AC250V、50HZ、1 min(imin(interrupting current≤500uA). AC250V、50HZ、5C CONTACT CIRCUIT
Addition 1.5-2 time force on the top of the key strok and press the switch,DC50V100mA 100mΩ Max
5D SWITCH CONNECTION FLASH
Addition DC5V on the two side of switch,at a speed of 3-5time a sec.to press the switch.The flash time between open not more than 10ms.
6.MECHANICAL EFFICIENCY 6A CONTACT STRENGTH
The contact shall be capable of a rorce of 5N for 5
seconds in any directions.
Switch electric andmechanical efficiency does not break
6B CONTACT JOURNEY
6C DRIVE FORCE
Being measure at across spring piece and across
6D CONNECTION
STRENGTH
A force of 1N being appling in any directions of the
switch connection partt.Switch mechanical
efficiency does not break.
6E
MECHANICAL LIFE
Operatin at a rate of 30-50 cycles a minute. 以
Life:100000ycles
7.ENVIRONME
NT—-RESISTANT EFFICIENCY 7A CHANGE OF
TEMPERATURE
The first temperature shall be 70 ℃ ,3h and
changed to-25℃,0.5h,5cycles of above test.
1. The appearance
should not break.
2. Contact
resistance ≤ 100 M Ω
3. Insulation
resistance ≥ 100 M Ω.
7B HUMIDITY RESISTANT
40±2℃ in temperature and 90-95%RH,Ruring
thetest time without load; After testing
the temperature should be 24h.
8.IOINTING EFFICIENCY
8A SOLDERABILITY
Temperature260±5℃;Duration;3±0.5S
Solderability part
should above 90%
8B
SOLDER—RESISTANT
Warm-up temperature:100℃,40S,
Froth height of assist
solder should under
board and switch electric and mechanical efficiency does not break.
8C JOINTING—RESISTANT
Jointing temperature: 260 ± 5 ℃ ,Duration of
immersion: 5±1S.
efficiency does not break
8D NORMAL JOLNTING TIMES
≤2times
Product detail pictures:
Related Product Guide:
We will devote ourselves to giving our esteemed buyers using the most enthusiastically thoughtful services for Factory Supply 4.5×4.5 Tact Switch - manufacturer 4.5×4.5 4 pin DIP tact switch – Shouhan, The product will supply to all over the world, such as: Egypt, UK, Hanover, So that you can utilize the resource from the expanding info in international trade, we welcome shoppers from everywhere on-line and offline. In spite of the good quality solutions we offer, effective and satisfying consultation service is supplied by our specialist after-sale service team. Product lists and detailed parameters and any other info weil be sent to you timely for your inquiries. So please make contact with us by sending us emails or call us if you have any questions about our corporation. ou may also get our address info from our web page and come to our company to get a field survey of our merchandise. We are confident that we are going to share mutual achievement and create strong co-operation relations with our companions in this marketplace. We're searching forward for your inquiries.
By Frederica from Kyrgyzstan - 2017.02.18 15:54
The after-sale warranty service is timely and thoughtful, encounter problems can be resolved very quickly, we feel reliable and secure.
By Muriel from Pretoria - 2018.12.11 11:26